Analisis Potensi Bahaya pada Kalibrasi Metering System Menggunakan Metode JSA
Abstract
The oil and gas industry carries high operational risks, particularly in metering system calibration activities. This research uses the Job Safety Analysis (JSA) method to find and examine possible risks in PT. X's metering system calibration procedure. Direct observation, conversations with engineers and HSE teams, and an examination of pertinent papers were used to gather data. Risk analysis was performed using a semi-quantitative approach by assessing the likelihood and severity levels for each identified potential hazard. The research identified 12 potential risks distributed across three categories: low risk (25%), medium risk (66.67%), and high risk (8.33%). The highest risk was found in the power transmitter isolation phase with electrocution hazard. Based on these findings, risk control recommendations are formulated which include training and certification, procedures, engineering controls and proper use of PPE. The implementation of comprehensive and systematic risk control is key to ensuring work safety and the extinction of company operations.
Downloads
References
I. Desti, “Literature RIview : Upaya Energi Bersih dan Terjangkau,” J. Sains Edukatika Indones., vol. 4, no. 1, pp. 8–11, 2022.
M. K. Herdyanti, “Analisis Kausalitas Konsumsi Energi Terhadap Pertumbuhan Ekonomi Di Indonesia,” PETROJurnal Ilm. Tek. Perminyakan, vol. 10, no. 3, pp. 122–129, 2021, doi: 10.25105/petro.v10i3.10839.
K. Sugiantara and M. Basuki, “Identifikasi dan Mitigasi Risiko di Offshore Operation Facilities dengan Menggunakan Metode Failure Mode and Effect Analysis,” J. INTECH Tek. Ind. Univ. Serang Raya, vol. 5, no. 2, pp. 87–92, 2019, doi: 10.30656/intech.v5i2.1775.
A. P. Nadyah Nurul Ramadhani, Nasrul, Dedy Takdir Syaifuddin, Sri Wiyati Maharani, “ANALISIS MEDIASI KEPUASAN KERJA PADA PENGARUH KESEHATAN KERJA, KESELAMATAN KERJA, DAN LINGKUNGAN KERJA TERHADAP KINERJA KARYAWAN,” vol. 1, no. 1, pp. 14–31, 2024.
M. Masripah, S. R. Pramukti, Z. Oktari, and M. Fadila, “Manajemen Risiko Pengendalian Mutu Pada Laboratorium Uji Dan Kalibrasi Prtbbn Sesuai Persyaratan Iso/Iec 17025:2017,” J. Stand., vol. 24, no. 1, p. 33, 2022, doi: 10.31153/js.v24i1.966.
S. Alimsyah and D. Davin, “Alat Pengukur Panjang Pipa Pada Pekerjaan Sumur Minyak Dan Gas Berbasis Mikrokontroler,” Sinusoida, vol. 22, no. 3, pp. 63–73, 2020, doi: 10.37277/s.v22i3.752.
D. Dwiyanti, “Pola Periode Kerja Perusahaan Minyak Dan Gas Pt. Xyz Di Sumatera Selama Masa Pandemi Covid-19 Terhadap Kinerja Karyawan,” Fair Value J. Ilm. Akunt. dan Keuang., vol. 4, no. 4, pp. 1091–1099, 2021, [Online]. Available: http://journal.ikopin.ac.id/index.php/fairvalue/article/download/798/383
U. N. Edi, “Program Pemeriksaan Teknis pada Sistem Alat Ukur Serah Terima Migas,” Swara Patra Maj. Ilm. PPSDM …, vol. 9, no. 1, 2019, [Online]. Available: http://ejurnal.ppsdmmigas.esdm.go.id/sp/index.php/swarapatra/article/view/187
M. Junaidi and N. Saidah, “Sistem Monitoring Kalibrasi Peralatan Migas pada BengkelInstrumentasi PPSDM Migas Cepu Menggunakan Java Netbeans,” J. Ilm. Inform. Komput., vol. 1, no. 2, pp. 7–12, 2022.
J. Heri, “Proses Sertifikasi Ketel Uap dan Bejana Tekan PT SUCOFINDO (Persero),” J. Sains Teknol. Transp. Marit., vol. 2, no. 2, pp. 16–23, 2020, doi: 10.51578/j.sitektransmar.v2i2.24.
G. J. SINAMUR and E. Utami, “Pertimbangan Hasil Pengukuran Laju Alir Pada Orifice Meter 071 Yang Berfungsi Untuk Custody Transfer Di X Metering Station (Xms) Xxxx Xxx Xxx (Xxx)Pty.Ltd,” Pros. Semin. Nas. Teknol. Energi dan Miner., vol. 2, no. 1, pp. 1273–1280, 2022, doi: 10.53026/sntem.v2i1.864.
E. Walujodjati and S. P. Rahadian, “Analisis Manajemen Risiko K3 Pekerjaan Jalan Tol Cisumdawu Phase III,” J. Konstr., vol. 19, no. 1, pp. 60–69, 2021, doi: 10.33364/konstruksi/v.19-1.874.
M. A. Fikri, N. Aini Mahbubah, and Y. P. Negoro, “Pengelolaan Risiko Kecelakaan Kerja di Open Area Konstruksi Berbasis Pendekatan HIRARC,” J. Surya Tek., vol. 9, no. 2, pp. 441–449, 2022, doi: 10.37859/jst.v9i2.4263.
M. Rizki Juniarto, M. Andivas, and M. Defran Vandhana, “Analisis Potensi Bahaya pada Perbaikan Threading di PT. XYZ Menggunakan Metode JSA,” J. Surya Tek., vol. 11, no. 1, pp. 211–216, 2024, doi: 10.37859/jst.v11i1.6467.
N. Saputra, A. Kisanjani, M. Andivas, and A. Angga, “Analisis Keselamatan dan Risiko pada Pekerjaan Pengembangan Kilang Minyak dan Petrokimia dengan Metode JSA,” J. Surya Tek., vol. 11, no. 1, pp. 296–299, 2024, doi: 10.37859/jst.v11i1.6519.
N. Rahmawati et al., “Strategies for Improving Occupational Safety in the ATBM Weaving Industry Strategi Peningkatan Keselamatan Kerja di Industri Pertenunan ATBM,” vol. 06, no. 02, pp. 297–309, 2024.
T. Nur Asih, N. Aini Mahbubah, and M. Zainuddin Fathoni, “Identifikasi Bahaya Dan Penilaian Risiko Keselamatan Dan Kesehatan Kerja (K3) Pada Proses Fabrikasi Dengan Menggunakan Metode Hirarc (Studi Kasus : Pt. Ravana Jaya),” JUSTI (Jurnal Sist. Dan Tek. Ind., pp. 1–32, 2021.
M. Riyan, P. Sukapto, and T. Yogasara, “Perbaikan Sistem Kerja untuk Meningkatkan Keselamatan dan Kesehatan Kerja (K3) Serta Produktivitas Melalui Pendekatan Ergonomi Partisipatif (Studi Kasus Di PT. Eka Karya Sinergi Bandung),” J. Rekayasa Sist. Ind., vol. 12, no. 2, pp. 237–250, 2023, doi: 10.26593/jrsi.v12i2.6784.237-250.
M. Andivas, W. Ismail Kurnia, P. Nuvira Mada, N. Febryantri Wahono, A. Hindarto Wibowo, and J. Pupuk Raya GnBahagia Kec Balikpapan Selatan Balikpapan Kalimatan Timur, “Analisis Kecelakaan Kerja Pada Refurbish Crane Dengan Pendekatan Metode HAZOP Analysis of Work Accidents in Refurbish Cranes Using the HAZOP Method Approach,” Metod. J. Tek. Ind., no. 10, p. 2024, 2024.
Muhammad Zulfi Ikhsan, “Identifikasi Bahaya, Risiko Kecelakaan Kerja Dan Usulan Perbaikan Menggunakan Metode Job Safety Analysis (JSA),” J. Teknol. dan Manaj. Ind. Terap., vol. 1, no. I, pp. 42–52, 2022, doi: 10.55826/tmit.v1ii.13.
Copyright (c) 2024 Fida Husnaseptia, Marulan Andivas, Misrianto, Dimaz Harits
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
Abstract views: 81 , 
*.pdf downloads: 113
