Analisis Kebocoran Instalasi Pipa Distribusi Steam pada Boiler untuk Tindakan Pemeliharaan di RSUP. Dr. M. Djamil Padang
DOI:
https://doi.org/10.37859/jst.v10i2.8726
Abstract
Boilers are one of the supporting facilities that play an important role in hospitals. The steam produced by the boiler in the form of saturated steam is used for laundry purposes and to sterilize medical equipment where the temperature must reach/exceed 270 oF. Therefore, the saturated steam produced by the boiler is a source of sterilization used in hospitals today, including RSUP Dr. M. Djamil Padang. The research was carried out to determine the factors that cause leaks and determine appropriate maintenance actions. Based on the research results, it was found that oxidation corrosion and thermal fatigue occurred due to overheating so that the steam distribution pipe cracked/leaked. Maintenance activities: Arranging water access, checking and calibrating temperature and pressure sensors regularly, retubing if the thickness of the distribution pipe is only 71% of the initial design size or painting to protect the pipe in contact with water and air, or the pipe is wrapped in rockwool to prevent metal from coming into contact with water and air
Downloads
References
Assauri Sofjan, 1998, Manajemen Produksi Dan Operasi, Edisi Revisi 1998, Jakarta.
Corder, Antony, 1992, Teknik Manajemen Pemeliharaan, Jakarta: Erlangga.
Dhillon, B.S.,2006, Maintainability, Maintenance, and Reliability for Engineers. New York: Taylor and Francis Group.
Djokostyardjo, M. J., 1999, Ketel Uap. Jakarta: PT. Pradnya Paramita.
Fithri, Prima, 2010, Optimasi Preventive Maintenance dan Penjadwalan Penggantian Komponen Mesin Kompressor Dengan Menggunakan Mixed Integer Non Linier Programming Dari Kamran, Thesis Master, Universitas Indonesia.
Handoko T Hani, 1991, Dasar-dasar Manajemen Produksi dan Operasi, BPFE, Yogyakarta.
Handoyo, Jusak Johan, 2016, Ketel Uap, Turbin Uap, dan Turbin Gas Penggerak Utama Kapal (Edisi 3), Djangkar: Jakarta.
Jardine, A.K.S., 1973, Maintenance, Replacement, and Reliability, Canada: Pitman Publishing.
Kitto, J.B. and S. Stultz, 2006, Steam its generation and use, 41st ed. Ohio: The Babcock & Wilcox Company.
Kurniawan, Fajar, 2013, Manajemen Perawatan Industri: Teknik dan Aplikasi Implementasi Total Productive Maintenance (TPM), Preventive Maintenance dan Reability Centered Maintenance (RCM). Yogyakarta: Graha Ilmu.
Mallikarjuna, V., Jashuva, N., & Reddy, B. R. B. (2014). Improving Boiler Efficiency By Using Air Preheater. International Journal of Advanced Research in Engineering and Applied Sciences, 3(2), 11–24.
Marwan dan Awig Dwi Sulistyo Budi, 1986, Pengelolaan Karyawan, BPFE, Yogyakarta.
Nurcahyo, R., 2006, Modern Maintenance Managemen and Spare part Management, Quality Buana Insani Colsulting: Jakarta.
Pratikto, 2008, Ketel Uap Pipa Air Bi Drum , CV. Asrori, Malang.
Setiawan, F.D, 2008, Perawatan Mekanikal Mesin Produksi, Maximus, Yogyakarta.
Siswanto, Yansen, 2010, Perancangan Preventive Maintenance berdasarkan Metode Realibility Centered Maintenance (RCM) pada PT Sinar Sosro. Skripsi, Universitas Sumatera Utara.
Soesetyo, I. dan Bendatu, L.Y., 2014, Penjadwalan Predictive Maintenance dan Biaya Perawatan Mesin Pellet di PT Charoen Pokphand Indonesia - 89 Sepajang, Vol. 2, No.2, Juni 2014, hlm. 147-154.
Soenoko Rudy, Gunadiarta Imade, 2009, Bahasan Termal Bahan-Bahan dan Ketel Uap, Jilid I,II, CV. Citra, malang.
Syamsir A. Muin, 1988, Pesawat-pesawat konversi energi (I): Ketel uap. Jakarta : Rajawali
Team, I. P.,2016, Pemeliharaan Mekanik Air Heater Level 1,2,3
Veen, Van Der, T., 1977, Teknik Ketel Uap, Educative Groepm: Jakarta.
Widharto Sri, 2005, Inspeksi Teknik, Buku 1, P.T. Pradnya Paramita, Jakarta.
